Maxtech xpm56i V.42bis Bedienungsanleitung

High PerformanceV.32bis/V.42bis14,400 BPS InternalFAX/Voice/DataModemUser's ManualContentsSection One Introduction ... 1S

9&D1 Modem returns to Command Mode after DTRtoggle&D2 Modem hangs up, returns to the CommandMode after DTR toggle&D3 Resets modem after

10&Zn=x n=0-3 Store telephone number x into non-volatileRAM%E_ %E0 V.22bis auto-retrain disabled%E1 V.22bis auto-retrain enabled%G_ %G0 Enable Aut

11\N4 V.42 data link only\O Initiate reliable link during a normal link\Q_ \Q0 Turn off flow control\Q1 XON/XOFF software flow control\Q2 CTS signal

12+FRH=<mod> Receive HDLC data+FRHM=<mod> Receive data+FRS=<time> Wait for silence+FRTn Fax receive test command+FTH=<mod> Tra

13Table 4-1 S - RegistersRegister Function Range/units DefaultS0 Auto-answer Ring 0-255/rings 0S1 Ring counter 0-255/rings 0S2 Escape code character 0

14BASIC RESPONSE CODESOK 0 CONNECT 1RING 2 NO CARRIER 3ERROR 4 CONNECT 1200 5NO DIALTONE 6 BUSY 7NO ANSWER 8 CONNECT 2400 10CONNECT 4800 11 CONNECT 7

15CONNECT 9600/REL-LAPM V.42BIS 68CONNECT 12000/REL-LAPM V.42BIS 69CONNECT 14400/REL-LAPM V.42BIS 70Section Six - TroubleshootingThis section describe

16identically.2. Make sure the phone line is working properly. Replace themodem with a regular phone and dial the number. If the linesounds noisy, you

171. Make sure the correct modem type is selected in the Voice/FAX software. Use “Cirrus Logic” or similar selection. Donot select “Rockwell or Rockwe

18possible. You will be informed of your right to file a complaintwith the FCC.Your telephone company may make changes in its facilities,equipment, op

1Section One - IntroductionThe 14.4 Kbps Series FAX/Voice/Data Modem con-nect your computer to all popular high speed modemsavailable today. This manu

19equipment meets certain telecommunications network protective,operational and safety requirements. The Department does notguarantee the equipment wi

1Section One - IntroductionThe 14.4 Kbps Series FAX/Voice/Data Modem con-nect your computer to all popular high speed modemsavailable today. This manu

23. If you have one or more serial ports on the back of yourcomputer, reconfigure your modem. Your modem is shippedset to COM1 on IRQ4. Reconfigure th

3Address should already be set by Windows to the COM portaddress used by the modem (refer to Table 2-1). Change theInterrupt Request Line (IRQ) to mat

4COM or IRQ setting for the modem is changed, thesettings in the software must be changed to match.2.5 Using Fax, Voice, and SpeakerphoneCapabilities

5“PHONE” on the back of the modem. Follow specific instruc-tions in the FAX/Voice/Speakerphone software on recordingand playback of voice prompts.2.6

6Section Three - AT Command Set3.1 Executing CommandsCommands are accepted by the modem while it is inCommand Mode. Your modem is automatically in Com

7T touch-tone dialingW wait for second dial tone, pause@ wait for five seconds of silence! flash; return to Command Mode after dialingDS=n Dial one of

8V_ V0 Numeric responsesV1 Word responsesX_ X0 Hayes Smartmodem 300 compatibleresponses/blind dialingX1 Same as X0 plus all CONNECT responses/blind di

9mode&T_ &T0 Ends test in progress&T1 Perform Local Analog Loopback Test&T3 Perform Local Digital Loopback Test&T4 Grant Remote Di

23. If you have one or more serial ports on the back of yourcomputer, reconfigure your modem. Your modem is shippedset to COM1 on IRQ4. Reconfigure th

10\Bn n=1-9 Send a 1/10 second line break to the modem,where n = 1 to 9. At normal connect, thedefault is 3\C_ \C0 Do not buffer data during LAPM/MN

11\Y Switch to reliable link from normal link\Z End the reliable connection and switch tonormal operation-J -J0 Disable error control detection phase-

12#VPH Telephone emulation mode.#VPL=n Play level. Default is 127#VPY Play mode#VRD Record mode#VRL=n Recording level. Default is 127#VSL=n Recording

13S17 ReservedS18 Modem test timer 0-255/seconds 0S19 ReservedS20 ReservedS21 DTR, DCD, DSR, and Bit-mappedLong Space DisconnectS22 Speaker and respon

14CONNECT 7200/REL-MNP 37CONNECT 9600/REL-MNP 38CONNECT 12000/REL-MNP 39CONNECT 14400/REL-MNP 40CONNECT 300/REL-MNP 5 42CONNECT 1200/REL-MNP 5 44CONNE

15Similarly, IRQ settings must be set correctly to receive datafrom the modem.3. Make sure that your modem is initialized correctly. Yourmodem may hav

16Modem experiences errors while communicatingwith a remote modem.1. Make sure the DTE speed is the same as the modem connec-tion speed when in Direct

17Temperature: 0 to 55 degrees C (Operating); -20 to 80degrees C (Non-operating)Section Eight - Support and ServiceIn the unlikely event you experienc

18harmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy, and if notinstalled and us

19themselves, but should contact the appropriate electric inspectionauthority, or electrician, as appropriate.NOTICE: The Load Number (LN) assigned to

3Address should already be set by Windows to the COM portaddress used by the modem (refer to Table 2-1). Change theInterrupt Request Line (IRQ) to mat

42.4 COM Port and Interrupt SettingsIf your computer is equipped with one or more serialports, you will need to change the COM Port setting on themode

5combination needed for your application. Any time theCOM or IRQ setting for the modem is changed, thesettings in the software must be changed to matc

6provide a user friendly method of accessing the functions youneed (i.e. dialing or answering calls).2.8 Where To Go From HereYou should familiarize y

73.3 Basic AT CommandsIn the following listings, all default settings are printedin bold text.Command FunctionA Manually answer incoming callA/ Repeat

8M2 Internal speaker always onM3 Internal speaker on until carrier detected andoff while dialingN_ N0 Connect only at DTE rateN1 Automatic rate negoti